Service Cars

If suddenly there was a knock on the steering rack VAZ, there is no need to immediately run to the station. All steering gear failure can establish their own hands. Only when independent work is necessary to be careful, very careful. To ensure security is tightened the hand brake, steering lock is made, as well as stops are located under the rear wheels. Still need to remove the negative terminal of the battery output. The work begins with the removal of the front wheels. To do this, use the jack. Then removed rod ends, with a special extractor. Nut clamps, through which the steering rack is attached to the body of the machine, you need to unscrew. To do this, apply a liquid WD - 40, which will facilitate your work. Then, using a flashlight to illuminate the portability, it is necessary to unscrew a bolt, which is located on the steering shaft is almost near the floor. And extract the steering rack after disconnecting from the tail shaft spline gears. Retrieved via rail, placed on the right hole. Then go in and apply a large bench vise. In order to clean the top rack, you need to take a cloth that is impregnated with white spirit, and a wire brush. To carry out such a procedure is required purity. After cleansing the body, to loosen the bolts that hold the mustache. Silent blocks an inspection to assess the possibility of further exploitation. After that we remove his mustache. To do this, turn down the plate and remove the bolts. At the end of the body are rubber plugs, remove them. Removed and the rubber cushion and rubber from the shaft gear. Using a screwdriver, removed from the bearing lock washer, and unscrew the nut. Together with the pinion bearing is removed. In order to do this, you must hold down the splined shaft and tap with a hammer to the body rails. Parts that were removed, washed in white spirit. Once all the parts cleaned, set it aside. And take out from the housing rack. In the absence of signs of wear on the rail, it washed, dried and then applied the new grease. Next, take out through the slot in the housing plastic sleeve, using a screwdriver. But be very careful that whatever hook and not to damage the aluminum landing a plane. If the damage aluminum nuts, you should immediately replace it. Lugs on the cover and mustache require scrutiny. If, as a result of testing on your fingers tips, were not found backlash, they can not be changed. After the inspection and rejection of superfluous details, finally, you can begin to build rail. Begin with the installation of a new plastic sleeve into the body rails, while acting absolutely must be in the slots. Set the rack on the side where the gear is located. With kolumbika, set the distance from the end rails to the body, it must be equal to 28 mm. Then put in place gear and pressed into the bearing until it stops. Then return to the place of focus and a spring, spinning lock nut. Next, put in place all the remaining parts, rubber boots. All operations were performed carefully to avoid damage.

Probably not in the light of such a driver who would not dream of high-quality acoustics. But all is not aware that the acquisition of expensive audio is half the battle, no less important - how to properly and correctly place the acquired dynamics and how they fit firmly. And only then can you milked the desired quality sound. Oh so there was market conditions that the manufacturers of high-quality audio systems do not bother to release podium for speakers. And motorists have-music fans themselves get out of this situation. To learn how to make a podium for speakers, we'll talk in this article. To begin to prepare the following materials and tools: 6 mm plywood, nylon fabric with high elasticity, epoxy glue, cheesecloth or fiberglass, and we need a stapler, assembly foam, sand paper, wrapping material for a podium and a suitable adhesive for gluing Tees material. The first thing to start - is to measure the location of the next stage and cut the ring at the door card. Then, using the jigsaw or other suitable tool drank from the plywood base and the ring itself. Select the desired angle and holds the base and the ring at this angle. To use the rack fastening of plywood, which in turn attach to the ring and the base with glue, for complete confidence in the reliability, you can attach a rack screws. So we should get frame podium. Once the glue dried out, the resulting frame fits elastic nylon cloth promazyvaem it in several layers of epoxy glue, held together by tissue stapler. Thus obtained cavity fill foam. We are waiting for dry foam. Here we note an important factor taken into account when making the podium diving depth and dynamics of its dimensions. The next stage - Cut off the excess foam formed with a knife and handle the entire surface with sandpaper. Then, in assembly foam impose a glass-fiber fillers. To the surface glistened and looked more smoothly, it is necessary to impregnate gauze or glass-fiber fabric with epoxy glue. Repeat this several times, in several layers. In order to achieve the strength and stiffness do not forget each time to pass over the surface with fine emery cloth. When the podium made in this way will be ready to begin wrapping his prepared material. It can be leather, leather, vinyl, etc. akrpet On leather and on the surface of the podium strike a thick layer of glue and covered the podium with the center to the edges, stapling the ends of the material stapler. Made their own hands the podium ready. And at the end of articles, a few tips. Podiums of foam convenient and cost-effective to manufacture, but remember to get a higher acoustic properties of sound, there must be resonating walls of the podium. This turn is only possible if for body podium will be used plywood thickness of 8-10 mm.

When Tinted windows motorists car driven by different reasons. But we want you to list the 6 main reasons for deciding to tinted windows. 1. Reduced heating the car up to 60% in hot weather. 2. Protection from possible skin cancer, because Tinted delays 99% of UV rays. 3. Tinted side windows keeps crashed, protecting you from cuts in the event of an accident. 4. Protects from harmful glare of the sun, oncoming headlights of a car and snow. 5. Hides the contents of the interior from prying eyes. 6. Protects the inner lining and plastic car from harmful sun rays, because they can burn and crack. Toning is made by attaching to the car window a special film. It is made of transparent polyester film on which the cause of a special metal and paint. Many believe that dubbing the film is too dark and there are problems when driving at night. But this is not true. Each film picks up with the required degree of dimming and to the same film reflects only the reflections, and the visible light passes. The film is mounted on the inner side of the automotive glass. If it is stuck on the outside, it may be subjected to mechanical damage, rain or snow. If you decide toned glass of your car, remember that in Russia prohibits tinted front glass film with transmittance below 85%. Before bonding the film to clean the glass surface from grease and dirt. On the glass surface should not be chopped off. Otherwise, in the bumps will form air bubbles. Hardest tinted rear glass, especially if there are installed blowing glass or stoplights. To make it easier to apply shading, some people take out the glass and run on your desktop. Can be carried out without removing the tinted glass. To do this, apply a papyrus paper to glass and depicts his path. After the cut pattern and drag it on tape. Cut film along the patterns. Next, wet the glass with the inside of the soap solution and apply the film. Tightens the tape on the ends to make it, exactly lay down on the surface. If possible, do not touch the film in the middle, otherwise it will wrinkle. After you install the film to sprinkle the surface of adhesive solution, paying particular attention to its edges. Once the film will fall perfectly, take a towel and remove excess mortar. Very gently pushing, keep the air bubbles and the remaining liquid, if any, to the edge. For best results, you can take a heavy object, and wrapped in a towel, smooth the surface of film dubbing.